පිපිරුම්-සාක්ෂි පහන් ස්ථාපනය කරන්නේ කෙසේද?

පිපිරීම්-ප්‍රතිරෝධී විදුලි පහන්, බොහෝ දෙනෙකුට නුහුරු යෙදුමකි, එදිනෙදා ගෘහ ජීවිතයේදී කලාතුරකින් හමු වේ. මෙම විශේෂිත විදුලි පහන් මූලික වශයෙන් කාර්මික සැකසුම් වල භාවිතා වේ, තෙල් ගබඩා සහ රසායනික කම්හල් වැනි, දැවෙනසුළු සහ පුපුරන ද්‍රව්‍ය පවතින තැන. පිපිරීම්-ප්රතිරෝධී විදුලි පහන් ස්ථාපනය කිරීම සම්මත බල්බ වලින් වෙනස් වේ, and there are specific considerations to keep in mind during their use. අද, let’s discuss these aspects.

Before installing an පිපිරීම්-ප්රතිරෝධී ආලෝකය, verify details from the nameplate and manual: the type, ප්රවර්ගය, ශ්රේණිය, group of explosion-proof, protection level of the casing, installation method, and requirements for fastening hardware. Ensure the light is securely fixed, with bolts and spring washers intact. Seals for dust and water resistance must be correctly placed. The cable entry must tightly fit the sealing gasket, be round and free of defects. Unused entries must be sealed according to the පිපිරුම්-ප්‍රතිරෝධී වර්ගය, with tightening nuts.

ස්ථාපන ක්රම:

Wall-Mounting:

Mount the light on a wall or support (ensuring the shading board is above the bulb), thread the cable through the joint, gasket, sealing ring to the junction box, leaving enough length for wiring, then tighten the joint and fixing screws.

Sloping Rod Suspension:

Pass the joint through the cable, screw it into the steel pipe, tighten the fixing screws, thread the cable through the gasket and sealing ring to the junction box, leave enough cable for wiring, screw the light into the joint ensuring the junction box is facing downwards. Adjust the copper joint and steel pipe to position the shading board above the bulb, ඉන්පසු සවි කරන ඉස්කුරුප්පු තද කරන්න.

Vertical Rod Suspension:

Similar to the sloping rod method, but with vertical positioning of the rod.

සිවිලිම සවි කිරීම:

Screw a 3/4 inch conversion joint into a pendant conversion joint, then thread the cable through, mount it on the ceiling, and follow the same cable threading and tightening procedures as before.

Installation Steps:

1. Identify the location and measure the distance from the light to the power source. Prepare a three-core cable of appropriate length, ensuring it’s longer than the distance.

2. Connect the wires by opening the lamp’s rear cover, threading one end of the cable, and connecting the live, neutral, and ground wires. Distinguish between neutral and ground for safety. සම්බන්ධතා වලින් පසුව, secure the cable with special tools and close the lamp cover.

3. Test the lamp by briefly connecting it to the power source. If the lamp doesn’t light up within 5 තත්පර, disconnect and recheck the wiring.

These guidelines aim to provide a basic understanding of installing explosion-proof lights safely and correctly.